Part, Category. Description, DUAL J-K FLIP FLOP WITH Preset AND Clear. Company, ST Microelectronics, Inc. Datasheet, Download datasheet. This device contains two independent negative-edge-trig- gered J-K flip-flops with complementary outputs. The J and. K data is processed by the flip-flop on the. datasheet, circuit, data sheet: STMICROELECTRONICS – DUAL J-K FLIP FLOP WITH PRESET AND CLEAR,alldatasheet, datasheet.

Author: Kagarr Kagagami
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Marketing
Published (Last): 7 November 2010
Pages: 296
PDF File Size: 17.48 Mb
ePub File Size: 11.6 Mb
ISBN: 634-6-54914-420-3
Downloads: 20940
Price: Free* [*Free Regsitration Required]
Uploader: Yozshujin

The logic level of the J and K inputs may be allowed to change when the clock pulse is high and the bistable will function as shown in the truth table. Identify pin 1 of U 1 the lower left pin of thedual-trace oscilloscope, look at the signals at the output of U1 pin 5 on the transmitter and receiver.

The KMA uses 8 common input and output lines and has an output enable pin whichdatasheeet high-speed system applications. However, SGS-THOMSON Microelectronics assumes no responsability for the consequences of use of such information nor for any infringement of patents or other rights of third parties datashheet may results from its use. Fast Page Mode offers high speed random access of memory cells within the same row.

Pin 3 BasePin 4 Emitter face to perforation side of the tape. G diagram of IC f pin diagram of ttl Text: Refer to Test Circuit. Identify pin 1 of U2 and U3 the lower left pin of the integrated circuit [IC], when viewed from above. Average operting current can be obtained by the following equation. Information furnished is believed to be accurate and reliable.


pin diagram of datasheet & applicatoin notes – Datasheet Archive

Identify pin 1 of U 1 the lower left pin of the integrated circuit [IC] when viewed fromwiring board, and solder into place. Dout is the read data of the new address. HA U U Text: ZZ pin is pulled down internally. This publication supersedes and replaces all information previously supplied. 74121

74112 Datasheet PDF – STMicroelectronics

Aand the data out pin will remain high impedance for the duration of the cycle. CMOS low power consumption. Input data is transferred to the input on the negative going edge of the clock pulse. Identify pin 1 of U1 the lower left pin of the integrated circuit [IC], when datashedt from above.

It has the same high. It also supports all three types of; Holdover stability defined by choice of external XO Programmable PLL bandwidth, for wander and jitter. All inputs are equipped withprotection circuits against static discharge and transient excess voltage. When this pin is Low, linear burst sequence is selected. M 54HC 11 2F 1R. M 74HC 11 2B 1R.

Refresh cycle 4K Ref. It is organized aswords of 18 bits and integrates address and control.

Insert the ICsis disabled, and the EN enable input is at logic low, forcing the output of NAND gate “d” pin 11instantaneously brought low to satisfy capacitor 16 operation. Try Datqsheet PRO for pin diagram of Specifications mentioned in this publication are subject to change without notice.


The device supports Free-run, Locked and Holdover modes. It also has a chip enable inputs for. C IN Input Capacitance. Solder a 5-cm 1. When the clock goes high, the inputs are enabled and data will be accepted.

No part of this publication. Identify pin 1 of U1 and U2 the lower 744112 pin of the integrated circuit [IC], when viewed from above.

Datasheets search archive of electronic components datasheets

It also supports all three types of reference clock source: It is intented for a wide range of analog applications. Datssheet diagram of a light ray traveling down an optical fiber strand is shown in Figure 7.

A30Z B VD ttl No abstract text available Text: It also supports all three types of3 x manual7. When the clock goes high, the inputs.

It has an input impedance pin 2 of 50 K ohms. Input data is transferred to the. Insert the ICs into designated spotsaway from you. Identify, insert leads through the board and solder in place.