89LV51RD2 DATASHEET PDF
Product Detail: Offer 89LV51RD2 PHILIPS, 89LVJU, 89LPCFDH from Hong Components In Stock Suppliers in 【Price】【Datasheet PDF】USA. 89lv51rd2 datasheet datasheet, cross reference, circuit and application notes in pdf format. PHILIPS[Philips Semiconductors]. Part No. P89LV51RB2 P89LV51RB2BA P89LV51RB2BBC P89LV51RC2 P89LV51RC2BN P89LV51RC2FA.
|Published (Last):||26 July 2006|
|PDF File Size:||11.47 Mb|
|ePub File Size:||10.71 Mb|
|Price:||Free* [*Free Regsitration Required]|
The data for Atlanta and Calgary are shown as in Figure 3b and Figure 3c. Select Animation Preview tab to preview animation.
P89LV51RD2 Datasheet(PDF) – NXP Semiconductors
Macro files can be edited directly under this Macro Tab. Figure 2a Figure 2b 3. Delay window allows users to select the delay period in second between images. Reset Device will appear as Figure 7a. Ng 89lv5rd2 Tor, Hassrizal B.
May 30, Page 5 of 12 b. Opening a macro 1. Basic steps to download images to the OLED display: Any images that have been selected datasjeet the Animation tab will be transferred to the hardware. All information contained in this document has been checked with the greatest care. Double click the Setup. Upon delivery, the firmware has already dagasheet downloaded to the board.
Dtasheet clicking on the start button for programming, the flash has to be erased by selecting either Erase all Flash or Erase blocks used by Hex File if the address of that specific block is known. At anytime, users can reopen any previously saved project by double-clicking on YourProject. Image with no specific name is applicable for both. Select Transfer to Display to execute the gamma input file and send it to the display module.
The file must reside in the gamma folder of the Pictiva directory. Next, remove datasgeet Reference Design board by using hexagon key 2. All macro files users create have to be saved in this new project folder before downloading them to the hardware. Images in the image folder at C: Refer to Figure 5. Figure 1 May 30, Page 3 of 12 2. The preview animation tab allows users to preview animation. Navigate to the directory where the Osram Pictiva has been installed, or navigate to C: Select the module which needed to program.
The typical value dataaheet Baud Rate is Further information is available at www.
Refer to Figure 4. Set interval delay between images if necessary.
【89LV51RD2 PHILIPS】Electronic Components In Stock Suppliers in 2018【Price】【Datasheet PDF】USA
Program the Calgary and Atlanta Display Module 1. Write pixel data to the display. The process is shown in Figure 2b. The data, time, and the locations of all the input files are displayed in this activity log field. The process is shown in the Figure 2a.
There are a few settings that need to be configured on the Flash Magic window before downloading the hex file: Launch Window Explorer 2.
Activity Log Tab The Activity Log records all the session activities while the Pictiva Display software is under execution, from a start time to an end time. Next, pull out the Calgary flex from the connector as shown in Figure 10b. Next, close up the connector as shown in Figure 11b.
The Figure 6 as shown below will be appearing. Calgary, x 64 2. It is divided into the following sections: Images start with atlxxx is meant for Atlanta Display Module whereas images start with calxxx is meant for Calgary Module display. Select a macro file, for example testloop. May 30, Page 6 of 12 Executing a macro Click on the Execute Macro button to download the content of the macro file to the hardware. If there is a massage popped up saying that the Baud Rate is too high, hen reduce the Baud Rate to Once all chosen images are on the Animation tab.
The Gamma Graph is the plot of gamma level from 1 to PPJ project file, the software automatically creates a folder, which has the same name and stores the file directory: Macros File Tab Macro file consist of commands that allow users to: Saving a macro 1.