ASTM F594 PDF

ASTM F594 PDF

or visit us at ASTM F Scope – This specification covers the chemical and mechanical requirements for stainless steel. ASTM F specification covers chemical and mechanical requirements for stainless steel nuts in diameters ranging from 1/4″ to /2″. ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. BoltPort.

Author: Jukinos Akinorr
Country: Qatar
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 11 July 2011
Pages: 341
PDF File Size: 14.15 Mb
ePub File Size: 1.49 Mb
ISBN: 116-7-79129-226-2
Downloads: 8747
Price: Free* [*Free Regsitration Required]
Uploader: Mozshura

ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard. Condition CW – When Condition CW is specified, the austenitic alloys shall be annealed in accordance with F54 A, generally by the raw material manufacturer and thenc old r594 to develop the specified properties.

A Tensile stress areas are computed using the following formula: Unless otherwise specified, all bolts, hex cap screws, and studs used with these nuts shall conform to the requirements of Specification F and shall be of the same alloy group. F When approved by the purchaser, alloys or Se may be furnished. A – Machined from annealed or solution annealed stock thus retaining the properties f5944 the original material; or hot formed and solution annealed.

Condition AF – When Condition AF is specified, the ferritic alloys shall be annealed in accordance to same above condition A Ferritic Alloys after all cold working including heading and threading has been completed. C The yield and tensile strength values for full size products shall be computed by dividing the yield and maximum tensile load value by the stress area for the product size and thread sizes determined in accordance with Test Methods F Link to Active This link will always route to the current Active version of the standard.

  CHEJOV PABELLON NUMERO 6 PDF

ASTM F594 Specification

Seven groups of stainless steel alloys are covered, including ten austenitic, two ferritic, four martensitic, and one precipitation hardening: E When approved by the purchaser, alloy F may be furnished. This specification covers the requirements for stainless steel nuts in specified size, inclusive, in nominal diameter in a number of alloys in common use and intended for service applications requiring general corrosion resistance.

Condition CW – When Condition CW is specified, the ferritic alloys shall be annealed in accordance to above condition A for ferritic alloys, generally by the raw material manufacturer and then cold worked to develop the specified properties.

A Unless otherwise specified on the inquiry and order, the choice of an alloy from within a group shall be at the discretion of the fastener manufacturer B See section 4. A Minimum values except where shown as maximum or as a range.

Free Technical Information

This abstract is a brief summary of the referenced standard. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use. Condition AF – When Condition AF is specified, the austenitic alloys shall be annealed in accordance to Condition A after all cold working including heading and threading has awtm completed.

  DESCARGAR ROGER PENROSE EL CAMINO A LA REALIDAD PDF

It is informational only and not an official part of the standard; the awtm text of the standard itself must be referred to for its use and application. The finished fasteners shall meet the applicable mechanical properties.

SH – Machined from strain hardened stock or cold worked to develop the specific properties. CW – Headed and rolled from annealed stock thus acquiring a degree of cold work.

Free Technical Information | Industrial Fasteners Institute

AF – Headed and rolled from annealed stock and then reannealed AH – Solution annealed and age hardened after forming CW – Headed and rolled from annealed stock thus acquiring a degree of cold work. Chemical tests; mechanical tests; and corrosion resistance shall be performed to conform with the specified requirements.

Historical Version s – view previous versions of standard.

D Yield strength is the stress at which an offset of 0. Referenced Documents purchase separately The documents listed below are referenced within the subject standard but are not provided as part of the standard. B legend of conditions: ASTM F covers seven groups of stainless steel alloys, including twelve austenitic, two ferritic, four martensitic and one precipitation hardening. AF – Headed and rolled from annealed stock and astk reannealed AH – Solution annealed and age hardened after forming.