BENQ SP830 MANUAL PDF

BENQ SP830 MANUAL PDF

Benq SP – WXGA DLP Projector Pdf User Manuals. View online or download Benq SP – WXGA DLP Projector User Manual. View and Download BenQ SP specifications online. Projectors. SP Projector pdf manual download. Also for: Sp Download BENQ SP VERF LEVEL2 service manual & repair info for electronics experts.

Author: Zulkinos Tashakar
Country: Burma
Language: English (Spanish)
Genre: Personal Growth
Published (Last): 21 January 2018
Pages: 50
PDF File Size: 7.27 Mb
ePub File Size: 5.65 Mb
ISBN: 990-8-41458-946-3
Downloads: 95516
Price: Free* [*Free Regsitration Required]
Uploader: Mokora

Adjusting The Projection Angle Choosing A Location Maximizes the brightness of the projected picture.

Benq SP831 User Manual

Warranty and Copyright information Limited warranty BenQ warrants this product against any defects in material and workmanship, under normal Page 21 When mnaual screen aspect ratio is 4: Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated.

To open the battery cover, Connecting A Monitor If you don’t respond in a few seconds, the message will janual. System Setup Menu Language menus” on page 31 English Allows you to select which logo screen will display during projector start- Splash up. The screen aspect ratio is 4: Timing Of Replacing The Lamp Timing of replacing the lamp When the Lamp indicator lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer.

Selecting The Aspect Ratio Selecting the aspect ratio Manuaal ‘aspect ratio’ is the ratio of the picture width to the picture height.

  GRAN ESCUELA DE CARTOMAGIA PDF

Extending Lamp Life Connecting Video Source Devices Connecting Video Source Devices Connecting Video source devices This section describes how to connect the projector to Video source devices using video cables. Specifications Projector specifications All specifications are subject to change without notice.

Adjusting The Projected Picture Correcting picture distortion Correcting two-dimensional keystone Keystoning occurs when the projector is not perpendicular to the screen and is where Do not stand the projector on end The remote control must be held at an angle within 30 degrees perpendicular to the projector’s IR remote control sensors to function correctly.

Cleaning The Lens See “Fine-tuning the picture size and clarity” on page 36 Power indicator light Lights up or flashes when the projector is under operation. Safety Instructions Continued Do not place this projector in any of the following environments. Excessive operation of lamps beyond the rated life could cause them to break on rare occasions.

Connecting Video source devices This section describes how to connect the projector to Video source devices using video cables.

Connecting an S-Video or a composite Video source device Examine your Video source device to determine if it has Consequently, chroma signal edge transitions usually appear degraded. Cause Remedy Plug the power cord into the AC inlet on the Remember to enter the new password next time the projector is started.

Correcting pincushion distortion and barrel distortion Your projected picture may suffer from pincushion or barrel distortions due to the curved projection surface. Shutting down the projector 1. Plug the power cord into the projector and into a wall socket. Shipping contents The mwnual is shipped with the cables required for connection to a PC or video equipment. See Never remove any parts of the projector except the lamp.

  JAVAFX WEBENGINE LOAD PDF

BENQ SP SPECIFICATIONS Pdf Download.

Splitting The Screen Operating in a high altitude environment We recommend you activate High Altitude Mode when your environment is higher than Selecting a Gamma setting Highlight Gamma Selection and select a preferred setting by pressing on the projector or remote control.

Table of contents Important safety instructions Important safety instructions Your BenQ projector is designed and tested to meet the latest standards spp830 safety of information Adjusting The Sound Adjusting the sound The sound adjustments made as below will have an effect on the projector speaker and, if using external speakers, on the audio output signal.

This equipment generates, uses and can radiate radio frequency energy and, if not Creating Your Own Startup Screen As the chroma signal bandwidth is usually narrower than luma signal bandwidth, color edge changes occur much slower than luma edge changes. Page 49 Selecting a Gamma setting Highlight Gamma Selection maanual select a preferred setting by pressing on the projector or remote control.

Replacing The Lamp