DESIGNJET T1300 SERVICE MANUAL PDF

DESIGNJET T1300 SERVICE MANUAL PDF

Print from a computer using the Embedded Web Server or HP Utility (T series). free Web service makes it easy to access and print large-format documents . It is possible to assign a manual IPv6 address to the printer, using the front. This Service Manual contains information necessary to test, calibrate, maintain and service the following: HP Designjet T 24inch; HP Designjet T 44inch;. HP DesignJet T and T Printer Series. Using your The only warranties for HP products and services are set .. Web Services manual configuration.

Author: Kebar Kazradal
Country: Guinea
Language: English (Spanish)
Genre: Technology
Published (Last): 7 August 2011
Pages: 297
PDF File Size: 2.38 Mb
ePub File Size: 19.77 Mb
ISBN: 434-1-61726-496-3
Downloads: 44207
Price: Free* [*Free Regsitration Required]
Uploader: Brarg

The Touch Control Panel asks you to remove the paper. Carriage and Cutter Assembly Removal Switch off the product and remove the power cable.

Center Covers Rear on page Page 76 Delete any non-standard paper preset in the product both the ones that have been srevice by the user and the ones that have been installed as OMES profiles through the EWS or the HP product Utility. Delete any non-standard paper preset in the product both the ones that have been created by the user and the ones that have been installed as OMES profiles through the EWS or the HP product Utility. The Cutter is designed to cut roll paper after printing to the defined sheet size.

An A4 or US Letter paper size is sufficient. Remove one T screw that secures the Window Position Deaignjet to the printer.

The Touch Control Panel then prompts you servide down Serviice 0. The information supplied is: Remove the Carriage Assembly. Page 70 Problem Description: If the bumper is correctly adjusted it should hold the paper.

  BSM 9101 PDF

Apply any common household cleaning dssignjet water based only to a soft, lint-free rag and apply it to the Drive Roller and Overdrive surface while it is rotating. The product performs two movements.

Use a flat-bladed screwdriver to unclip the left Print Zone Overdrive retaining clip and rotate the clip vertically.

Encoder Strip, spring and attachment nut on page Remove the top T screw that secures Ink Supply Tubes guide to the product.

Remove a printhead by lifting up the blue handle. Therefore, you are recommended to proceed in the following order. See Customer Self Repair parts. Carefully lift the Ink Supply Tubes guide enough until you can slide it forwards out of the product. Before using this chapter to remove and install a new component, always make sure that you have performed the relevant service test from Chapter 4. The changes made by this utility take effect only after the product has dessignjet restarted.

HP Designjet T / T / T series. Service Manual

Paper Path Assemblies Rear. Leave the sensor to one side to remove the collar Remove the collar by sliding it in the direction indicated Installation Installing the Right Collar is the same as the removal procedure, however care must be taken with the Cable and Sensor of the Scanner Position ,anual.

Insert the printhead slowly and vertically, straight down. Click the file once to select it, then right-click and select Save target as. Unable to pressurize the Ink Delivery System Corrective action: Insert the new bumper screw into the bracket and turn in a clockwise direction.

Remove all the Printheads.

Page Confirm your selection by pressing OK. Be careful with the paper sensor cable.

Encoder Manula and Encoder Sensor on msnual Please return to the product information page and verify the numbers provided or try again later. Unscrew the screw as shown. Remove four T screws and remove the Front Roller Cover. It may be damaged if you insert it too fast, or at an angle, or if you rotate it as you insert it.

  BLENDER HANDBUCH 2.6 PDF

Center Covers Front 2 of 3 on page Window Position Sensor Removal Switch off the printer and remove the power cable. The PRS subsystem is designed to move the carriage assembly between two predetermined vertical positions with respect to the plane of the print platen.

Page Rewinder Adjust The Rewinder Adjust utility clears the calibration parameters associated with a Rewinder motor when it has to be replaced. Shut down the product and replace t13300 drop detector. Open the upper roll cover and press OK. Wait for the unit to complete the booting process.

Install only new parts recommended by HP for this product.

HP DESIGNJET T1300 ePrinter series Service Manual

The Touch Control Panel prompts you to insert all the ink cartridges. Move the right side of the converger in the direction of the arrow, then remove the whole converger from the product. Problem with the firmware upgrade process Corrective action: Unscrew the small cover of the Carriage PCA. Remove four T-8 screws that secure the Carriage Assembly Cover hinge. The carriage should not offer resistance to manual movement.

Remove the two front T screws that secure Ink Supply Tubes guide to the product.